An old brick or stone fireplace looks great… but most of the heat goes straight up the chimney. A wood insert lets you keep the charm of your masonry fireplace while turning it into a real heating appliance that actually warms your home. By upgrading to a wood insert, you get more comfort, more heat, and less dependence on other heating sources like electricity or gas. What is a wood insert and why choose one? A wood insert is a wood-burning appliance that slides directly into the opening of your existing masonry fireplace. Think of it as a modern wood stove built to fit inside your old hearth. Unlike an open fireplace that loses most of its heat through the chimney, a wood insert: Burns wood in a closed firebox Uses an integrated fan to push warm air back into the room Holds onto much more of the heat you create If you have a large living room or an open-concept area that your current fireplace barely warms, a wood insert is a simple way to turn that spot into a powerful heat source. On The North Flame, you can browse wood inserts that are built for real performance, not just looks. Key benefits of replacing your old masonry fireplace Upgrading to a wood insert gives you both comfort and savings. Here is what you gain when you make the switch. 1. Much better energy efficiency Traditional masonry fireplaces are beautiful, but they are not efficient. Most of the heat disappears up the chimney. A wood insert is designed to keep that heat inside your home. The closed firebox and blower push warmth into the room, so you: Get more heat from every load of wood Reduce wasted energy Enjoy a more even, comfortable temperature When you look at our wood inserts, check the efficiency ratings and heating area on each product page to match them with your space. 2. Lower heating bills Because a wood insert gives off more usable heat, you can rely less on electric or gas heating. Over time, that can mean: Lower energy bills A more stable and predictable heating cost Less stress during peak rate periods or cold snaps If you want your fireplace to actually help you save money instead of just looking nice, a high efficiency wood insert is a smart move. 3. Simple, clean installation You do not need a major renovation to upgrade. Wood inserts are built to fit into existing masonry fireplaces with the right venting setup. That means: No tearing down your hearth A cleaner, faster installation A modern heating appliance that still respects the original look of your fireplace When you choose a model from our store, you get a unit designed to slide into your existing opening with a clean, finished look. 4. Safe, reliable heat A quality wood insert gives you a dependable source of heat, even if the power goes out. That is a big advantage in the middle of winter. You benefit from: A sealed door that reduces the risk of sparks and embers A controlled burn that is easier to manage than an open fire Consistent heat output to keep your family comfortable For many homeowners, that extra layer of security alone justifies the upgrade. 5. Better for the environment Modern, high efficiency wood inserts are designed to burn cleaner than old open fireplaces. With the right model, you: Use less wood for the same heat Reduce smoke and fine particle emissions Lower your overall environmental impact All of our wood inserts are EPA or CSA certified, which helps you choose an appliance that respects current environmental standards. What is secondary combustion and why does it matter? Most older fireplaces and basic appliances burn wood in a single stage. The problem is that a lot of the gases and fine particles in the smoke never get burned. They leave as wasted fuel and extra pollution. Certified wood inserts and modern stoves use secondary combustion to fix that. Here is how it works. Preheated air is introduced through secondary air tubes inside the firebox. This extra hot air mixes with the unburned gases and particles from the first combustion. Those gases ignite a second time, creating extra flames at the top of the firebox. This has several big advantages for you: More heat from the same amount of wood Less smoke and fewer fine particles released into the air Longer, more stable burn times between reloads In short, secondary combustion means you get a hotter, cleaner fire while using less fuel. When you look at wood insert product pages, watch for mentions of secondary combustion or clean burn technology to make sure you get these benefits. Comfort, efficiency, and a modernized fireplace Switching from an open masonry fireplace to a wood insert is one of the easiest upgrades you can make if you want: Real, usable heat instead of a decorative fire Lower heating costs and less reliance on electricity A cleaner, safer, and more efficient appliance A modern heater that keeps the traditional look of your hearth If you are ready to turn your old fireplace into a serious heat source, a wood insert is the way to go. Next step: explore high efficiency, Canadian-made wood inserts on The North Flame, compare heating capacity and features, and choose the model that best fits your home and your lifestyle. That is how you turn a rarely used fireplace into one of the most valuable heating tools in your house.

How to Choose the Right Wood Stove for Your Home Picking a wood stove is not just about looks. To get the right model, you need to think about where it will be installed, how your home is laid out, and how you plan to use it. Then, you can calculate your heating area and match it with a stove that actually fits your needs. Once you know your numbers, you can browse stoves that match your heating area and lifestyle and choose the unit that will work best in your home. 1. Where will the wood stove be installed? Location matters a lot. If you install a stove in the basement, the heat will rise and help warm the first floor. If you install it on the first floor, it generally will not heat the basement. High or cathedral ceilings let a lot of heat move upward, so some of that warmth is lost higher up instead of staying at your level. Knowing where you plan to place the stove will help you judge how far the heat can realistically spread. 2. Does heat move easily through your space? The layout of your home changes how well a wood stove can do its job. Open floor plans and nearby rooms are easier to heat. A home with many small, closed-off rooms is harder to warm evenly because hot air does not circulate as well. A wood stove should be seen as a secondary heat source. It adds comfort, reduces the load on your main system, and gives you that cozy fire feel. If you want more even heat throughout the house: A blower can help push warm air into nearby areas. For full-house, balanced heating, a wood furnace is often more efficient than a stove alone. When you shop our stoves, think about whether you want targeted comfort around the unit, or something that works with your overall heating strategy. 3. How good is your insulation? The better your home is insulated, the more heat it can hold. Factors that affect this include: Number and size of windows and doors Type and quality of windows and doors Orientation (for example, large north-facing windows may lose more heat) Thermal resistance (R value) of your walls and roof Two stoves with the same heating capacity will not perform the same way in a drafty house versus a well-insulated one. If your home is older or less insulated, you may need a stove with a bit more power than the basic calculation suggests. 4. How do you plan to use the wood stove? Your usage makes a big difference: Sustained use: You use the wood stove as a strong additional heat source and run it regularly to get as much heat as possible. Ambiance use: You mainly want comfort and atmosphere around the appliance, with gentle extra heat rather than maximum output. Being honest about how often and how intensely you plan to use the stove will help you choose the right size and model. On each product page, look at both the heating capacity and the type of use it is best suited for. 5. Calculating the theoretical heating area The theoretical heating area is your starting point. It is a basic estimate of the space your stove could heat, based on the floor it is on and the floors above. Here is a simple rule: Theoretical area to heat =100% of the floor where the stove is installed 50% of the floor above 25% of the next floor (if there is one) Example: You install a wood stove in the basement of a 2 storey house with 800 ft² per floor. Floor 1 (basement, where the stove is): 100% of 800 ft² = 800 ft² Floor 2 (main floor): 50% of 800 ft² = 400 ft² There is no third floor in this example, so 25% of floor 3 = 0 Total theoretical heating area: 800 + 400 + 200 = 1,400 ft² (If there was a third floor, you would add 25% of that floor as well.) Once you have this theoretical area, you can start looking at stoves that list a similar heating capacity in their specifications. 6. Adjusting to get the real heating area Theoretical area is a baseline. To get closer to real life, you adjust that number with a comfort margin based on your conditions and how you will use the stove. Other factors that affect performance: Humidity Wood quality Chimney design and draft Outdoor temperature and wind Here are two examples, using a theoretical heating area of 1,400 ft²: 1. Very favorable conditions Ambiance use Good insulation Good air circulation In this case, it is recommended to choose a stove that slightly exceeds the theoretical area and aim for a real heating area around 1,600 ft². 2. Less favorable conditions Sustained use Poorer insulation Limited air circulation Here, it is better to add a larger comfort margin and aim for a stove rated around 1,800 ft² to 2,000 ft². When you visit our wood stove collection, you can compare the heating capacity listed on each product page with your real heating area to quickly narrow down the best models. 7. Finding the right power: not too big, not too small Choosing a slightly more powerful unit has clear advantages: Higher overall heating capacity Ability to load larger or longer logs Longer burn times between reloads But you also need to avoid going too far in either direction. If the stove is too big:Many people compensate by making small, cool fires. That leads to poor combustion, more creosote in the chimney, and lower efficiency. If the stove is too small:You may end up running it at maximum output all the time. This can cause faster wear on the appliance and still may not fully meet your heating needs. The goal is to match the stove’s rated heating area with your real heating area and how you plan to use it. Turn your numbers into the right stove Once you know: Where your stove will be installed How open or divided your space is How well your home is insulated Whether you want ambiance or sustained heat Your theoretical and real heating area you are ready to choose a model with confidence. From there, you can head our Wood Stove collection, filter stoves by heating capacity, and compare a few models that match your real heating area. That way, you are not just buying a beautiful wood stove, you are choosing one that will actually keep your space warm and comfortable for years.

Installing a wood stove or fireplace is a great way to make your home feel warm and welcoming, while cutting down on heating costs. But there is one step that should never be skipped: protecting the floor under and around your unit. A hearth pad or floor protection board is not just a nice accessory. It is a key safety component and, in many cases, a requirement to meet Canadian installation standards. If you are planning to install or replace a stove or fireplace, this is the first upgrade you should look at. You can see our full selection of hearth pads Why Floor Protection Is Required A stove or fireplace produces very high temperatures. Over time, that heat can damage flooring like wood, vinyl, or laminate. On top of that, sparks or embers can escape the firebox and land on the floor. Without protection, that can cause burns, scorch marks, or even a house fire. Floor protection is designed to shield any combustible material around your stove, such as: Wood or laminate flooring  Vinyl floors Rugs and carpets Furniture and nearby decor In Canada, a properly sized, non combustible floor protector is part of a code compliant installation. Standards such as CSA B365 apply across the country, and your province or municipality may have extra rules. Your appliance manual will also specify what type of floor protection is required. If you are not sure what you need, choosing a certified hearth pad from a trusted store is the easiest way to stay within code. How To Choose the Right Hearth Pad To protect your home and stay compliant, your floor protection needs to meet a few basic criteria. 1. Size of the hearth pad The pad has to cover the floor directly under the unit and extend far enough in front and on each side. In many Canadian installations, minimum clearances are: 18 inches in front of the appliance 8 inches on each side These are general guidelines only. Every stove or fireplace model is different, so always follow the clearances in your manufacturer’s installation manual. When in doubt, choose a pad that is a bit larger rather than too small. In our hearth pad collection, you will find different shapes and sizes so you can match your appliance and layout. 2. Material of the hearth pad The floor protector must be made from non combustible materials. Common examples include: Metal Tempered glass Ceramic tile Brick Cement or concrete board These materials handle high temperatures and offer the durability you need for daily use. When you shop our hearth pads, you can filter by material and pick the look and performance that best fits your stove and your decor. 3. R value and thermal protection Some appliances require a hearth pad with a specific R value. R value is simply a way of measuring how well a material resists heat transfer. If your stove or fireplace manual mentions a minimum R value for floor protection, your pad must meet or exceed that number. That is what ensures your installation is safe and compliant. If you need help choosing a hearth pad with the right thermal protection, you can start by browsing our certified models   Clearances and Combustible Materials Flooring is not the only thing at risk. Anything combustible near your stove or fireplace has to be protected and kept at the right distance. This includes: Wood: walls, trim, floors, shelves, furniture Fabrics: curtains, rugs, cushions, clothing Plastics: decor, storage bins, furniture Paper or cardboard: books, newspapers, boxes Composite panels or laminate wall coverings If these items are too close, they can: Overheat and catch fire Dry out and deteriorate over time Become uncomfortable to use because of excessive heat Your installation manual will list required clearances to combustibles. Floor protection and a properly sized hearth pad help you respect those clearances, especially in front of the stove where sparks are most likely to fall. What Happens if You Skip Floor Protection Installing a stove or fireplace without proper floor protection is a serious risk. The combination of radiant heat, hot embers, and falling logs can: Burn or permanently stain your flooring Damage wood or composite subfloors Start a fire that spreads beyond the appliance Wood and many composite materials are not made to handle the temperatures generated by a stove or fireplace. A hearth pad acts as your first line of defense. It is not a luxury item. It is a basic safety measure that protects your investment and your home. Make Your Installation Safe and Code Compliant Whether you are setting up a new stove or updating an existing hearth, floor protection should be part of your plan from day one. The right hearth pad will help you: Meet Canadian installation standards Protect your floor and nearby materials Improve safety and extend the life of your appliance If you are ready to upgrade, you can browse our collection of certified hearth pads Pick the size, material, and style that match your stove, then complete your order online. That way, by the time your installer arrives, you already have a compliant, good looking hearth pad ready to go.